Status-
Besucher
| Heute: |
|
195 |
| Gestern: |
|
460 |
| Gesamt: |
|
15032425 |
-
Benutzer & Gäste
4930 Benutzer registriert, davon online: 211 Gäste
|
|
|
| 18575 Beiträge & 12638 Themen in 21 Foren |
Keine neuen Beiträge, seit Ihrem letzten Besuch am 23.04.2026 - 11:56.
|
|
|
|
|
|
| Autor |
|
 |
dinghl |
|
|
|
|
|
Negative pressure systems are generally used for transporting material from one or more entry points to a single exit point. The configuration of ponents in this type of system is feeder Nike Air Max 90 Independence Day Pas Cher , separator, and then fan as shown in Figure 2. This type of system is almost always used where toxic materials are being handled because any leakage is into the system. Negative pressure systems are generally used for transporting material from one or more entry points to a single exit point. The configuration of ponents in this type of system is feeder, separator, and then fan as shown in Figure 2. This type of system is almost always used where toxic materials are being handled because any leakage is into the system. Material is fed into a negative pressure system (fan downstream of feeder and separator) using one of several methods. Mechanical methods may be used, such as in the positive pressure setup. Alternatively, a simple feeder, such as a duct opening Nike Air Max 90 Homme Pas Cher , may be sufficient if the material is light enough for the amount of vacuum the fan creates. Hopper fed elbows can be useful as any extra material not collected in the air stream will fall down the elbow and can be re-used. The negative pressure system is well suited for applications such as unloading rail cars. Another application would be for handling toxic materials so that any leakage would be into the system. Grains, seeds, granular chemicals, and pellets have been suessfully transported using this method. In this type of system, since the fan is downstream of the separator, the amount of material going through the fan is minimized. Therefore, the wear and tear on the fan is limited. Another advantage to this type of system is that any leakage is into the system Nike Air Max 90 Femme Pas Cher , thereby eliminating dust problems. The disadvantage to this type of system is that if the loading is high or the length of the system is large, the ponents must be designed for high vacuum. This adds cost to the ponents and must be considered when paring methods of transport. The material loading is the ratio of the weight flow of the material to that of the air. For any given material, there is a minimum transport velocity required to convey the material. Therefore, the airflow rate will depend several different pipe duct sizes may be used, but only one will be the most economical. There is quite a range of suggested material loadings for a particular setup, so it is remended to consult with a pneumatic conveying expert prior to making any calculations. Typically, a material loading of anywhere from 2:1 to 1:1 or less is aeptable for standard industrial fans. Pressure blowers may be used up to material loadings of 6:1. Over that http://www.chaussureairmax90pascher.fr/ , more specialized designs, such as multiple fans or multiple stage blowers, may be required. Once a pipe size has been selected, the airflow rate can be calculated based on the minimum transport velocity of the material being handled. Once the calculations for the system have been performed and the appropriate pipe size has been selected based on material being conveyed and system resistance, the fan operating point is a simple calculation. The required flow rate of the fan is simply the velocity multiplied by the area. If the material being conveyed will be going through the fan, special considerations must be given to the fan design. Several factors must be considered in order to select the appropriate fan for the application being considered. The fan blade type selection is very important because one does not want to select a blade type that is prone to collecting material. Backward curved and airfoil blades are efficient, but are better suited for clean air applications because they often collect material on the blades. Radial blades are better suited for material handling applications. Backward inclined blades and blades that have a radial tip have also been used suessfully in certain material handling applications. Fan speed is also important in selecting a fan for material handling. The operating speed should be minimized as much as possible. High-speed fans with high tip speeds create higher velocities that correspond directly to the level of erosion and impact on the fan and system ponents. The fan should be selected with the critical speed significantly higher than the operating speed. A good rule of thumb for material handling fans is to keep the rigid support critical speed at least 1.5 times greater than the operating speed. Special materials may be required to resist corrosion Nike Air Max 90 Chaussures , abrasion, and impact depending on the material being handled. In some applications, liners are added to the fan wheel at locations where the most abrasion will our. These liners can then be replaced periodically without having to replace the entire wheel. The level of abrasion of the material will determine the level of erosion protection needed. Some applications may only require a special coating, while others may require special material liners to be installed on the fan wheel and or housing. Special coatings may also be required to resist corrosion or to make cleaning easier. Oversized aess doors may be used to make maintenance and cleaning easier to acplish. Special construction of the housing, known as swing-out and clamshell, allow for easy aess to the fan ponents for cleaning and maintenance. In swing-out construction, the fan wheel Nike Air Max 90 Prix , shaft, bearings, and motor are mounted on a door. The door can be opened for easy cleaning of fan ponents without removing ductwork. Shaft seals may be required to resist materials from leaking out around the fan shaft. If the material being handled is explosive or flammable, spark resistant construction is required. AMCA Standard 99 specifies Type A, B, and C spark construction, which are available for many fan designs. If materials such as coal are being transported Nike Air Max 90 Pas Cher , the National Fire Protection Association requires the fa
|
| Beitrag vom 08.07.2015 - 06:35 |
|
|
|
